Honeywell RTH230B udhëzues

Honeywell RTH230B
9.2 · 2
PDF udhëzues
 · 4 faqe
Anglisht
udhëzuesHoneywell RTH230B
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
a gas, fuel oil or electric furnace - 2 or 3 wires
a central air conditioner - 2 or 3 wires
a hot water system with or without pump - 2 wires
a millivolt system - 2 wires
a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
System operating mode selection: heat, cool or off
Fan operating mode selection: automatic or on (continuous)
Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
Temperature display in °F or °C
Battery replacement indicator
5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
o Identify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 1/4 inch).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to
avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.

n Remove the thermostat faceplate.

o Loosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

p Tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
GFan

Shikoni udhëzuesin për Honeywell RTH230B këtu, falas. Ky udhëzues hyn në kategori termostat dhe është vlerësuar nga 2 njerëzit me një mesatare prej 9.2. Ky udhëzues është i disponueshëm në gjuhët e mëposhtme: Anglisht. A keni ndonjë pyetje në lidhje me Honeywell RTH230B apo keni nevojë për ndihmë? Bëni pyetjen tuaj këtu

Keni nevojë për ndihmë?

A keni një pyetje në lidhje me Honeywell dhe përgjigja nuk është në manual?

  • Merrni përditësime për zgjidhjet
  • Merrni përgjigje për pyetjen tuaj

Pyetje dhe përgjigje

Numri i pyetjeve: 0

Termoshtati Honeywell RTH230B është një pajisje elektroike që kontrollon dhe rregullon temperaturën e ambienteve. Pajisja është në formë rrethore dhe ka një ekran LCD ku përdoruesi mund të kontrollojë dhe të ndryshojë temperaturën. Termoshtati është i dizajnuar të jetë i lehtë për tu instaluar dhe është kompatibël me shumë sisteme HAVAC. Në mënyrë që të ofrojë një përvojë më të mirë të përdorimit, termostati ka funksione të ndryshme si një sensor temperaturë për të regulluar sistemin HAVAC në varësi të temperaturës, një programues që lejon përdoruesin të zgjedh afatet kohore dhe temperaturën për të optimizuar funksionimin e sistemit, dhe një funksion mbrojtës që ndalon sistemin në rast të ndonjë problemi ose mungese energjie elektrike. Përveç kësaj, të gjitha funksionet janë shfaqur në ekran në një mënyrë të kuptueshme për ta bërë atë të lehtë për tu përdorur dhe të kuptojnë. gjithashtu, Honeywell RTH230B është një termoshtat i përshtatshëm për të ndryshuar nga çelësat manuale në mënyre që të sigurojë kontroll të shpejtë dhe të lehtë të temperaturës në ambient.

Të përgjithshme
MarkëHoneywell
ModelRTH230B
Produkttermostatet
GjuhaAnglisht
Lloji i skedaritUdhëzuesi i përdoruesit (PDF)

Nuk mund ta gjeni përgjigjen e pyetjes suaj në udhëzues? Ju mund të gjeni përgjigjen e pyetjes suaj te Pyetje dhe Përgjigje të Shpeshta rreth Honeywell RTH230B më poshtë.

Ku është vendi më i mirë për të vendosur termostatin?

Vendi më i mirë për termostatin është dhoma ku kaloni më shumë kohë, në shumë raste dhoma e ndenjes ose kuzhina. Vendoseni termostatin rreth një metër e gjysmë mbi dysheme, jo në diell dhe jo në një mur të jashtëm.

Cila është brezi i vdekur i një termostati?

Nëse termostati juaj ka një brez të vdekur, instalimi juaj është, si të thuash, "në pushim". Termostati ndizet vetëm kur, për shembull, diferenca devijon më shumë se 2˚C nga temperatura e caktuar e dhomës.

Cila është temperatura ideale e dhomës?

Shumica e njerëzve zbulojnë se temperatura ideale e dhomës është midis 19 dhe 22 gradë celsius.

A është udhëzuesi i Honeywell RTH230B në dispozicion në Shqiptar?

Fatkeqësisht, ne nuk kemi udhëzues për Honeywell RTH230B në dispozicion në Shqiptar. Ky udhëzues është i disponueshëm në Anglisht.

A nuk është listuar pyetja juaj? Bëni pyetjen tuaj këtu

Nuk ka rezultate